Opel Omega

since 1993-1999 release

Repair and operation of the car


Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Repair of engines
+ 4. Heating system and ventilation
- 5. Fuel, exhaust systems
   - 5.1. Petrol engines
      5.1.1. Technical characteristics
      5.1.2. Unleaded gasoline
      5.1.3. Systems of injection of fuel
      5.1.4. Air filter and air branch pipes
      5.1.5. Accelerator rope
      5.1.6. Accelerator pedal
      5.1.7. Release of pressure from system of injection of fuel
      5.1.8. Fuel pump
      5.1.9. Fuel level sensor
      5.1.10. Fuel tank
      5.1.11. Case of a butterfly valve
      + 5.1.12. Elements of system of injection of fuel (2,0 l engine)
      5.1.13. Inlet collector
      5.1.14. Final collector
      5.1.15. Multiline system of air supply
      5.1.16. System of production of the fulfilled gases
      + 5.1.17. Systems of decrease in toxicity of exhausts
   + 5.2. 2,0 liters diesel engine
   + 5.3. Diesel V6 engine of 2,5 liters
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


785173a6

5.1.15. Multiline system of air supply

GENERAL INFORMATION

This system serves for increase in engine capacity at any turns of the engine. The system consists of the preliminary camera and two gates, one of which is established in an airintaking branch pipe, and the second – in the top section of an inlet collector. Position of gates is regulated by an electronic control unit depending on the speed of operation of the engine.

For testing and check of system it is necessary to address experts.

THE SOLENOID OF THE GATE INSTALLED IN THE AIRINTAKING BRANCH PIPE

The solenoid is located in a back part of the preliminary camera.

Removal and installation

PERFORMANCE ORDER
1. Disconnect the socket of connection of the solenoid and disconnect vacuum tubes. Turn off fixing screws and remove the solenoid (it is specified by an arrow).
2. Installation is carried out to the sequences, the return to removal.

THE GATE LOCATED IN THE AIRINTAKING BRANCH PIPE

Removal and installation

PERFORMANCE ORDER
1. Disconnect an idling speed regulator hose from an airintaking branch pipe.
2. Remove branch pipes.
3. Disconnect a vacuum hose from a gate diaphragm.
4. Turn off fixing screws and remove the gate (the screw is specified by an arrow).
5. Installation is carried out to the sequences, the return to removal.

THE SOLENOID OF THE GATE INSTALLED IN THE INLET COLLECTOR

The solenoid is located on the left back part of an inlet collector.

Removal and installation

PERFORMANCE ORDER
1. Disconnect the socket of connection of the solenoid, disconnect vacuum tubes. Turn off fixing screws and remove the solenoid (it is specified by an arrow).
2. Installation is carried out to the sequences, the return to removal.

THE GATE LOCATED IN THE INLET COLLECTOR

Removal and installation

PERFORMANCE ORDER
1. Remove the top section of an inlet collector.
2. Disconnect a vacuum hose from a gate diaphragm. Turn off fixing bolts (are specified by shooters) and remove the gate.
3. Installation is carried out to the sequences, the return to removal.

PRELIMINARY CAMERA

Removal and installation

PERFORMANCE ORDER
1. Remove the air stream sensor.
2. Remove airintaking branch pipes.
3. Disconnect the socket of connection and a vacuum hose from the gate solenoid.
4. Turn off fixing nuts and remove the camera.
5. Installation is carried out to the sequences, the return to removal.