Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Repair of engines
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
- 11. Brake system
11.1. Technical characteristics
11.2. Brake overlays of forward brakes
11.3. Brake overlays of back brakes
11.4. Support of a forward brake
11.5. Support of a back brake
11.6. Brake disk
11.7. Brake shoes of the emergency brake
11.8. Rope of the emergency brake
11.9. Lever of the emergency brake
11:10. Main brake cylinder
11:11. Tank of brake fluid and sensor of level of liquid
11:12. Pumping of the brake system
11:13. Hydraulic tubes and hoses
11:14. Vacuum hose and valve of the vacuum amplifier of brakes
11:15. Vacuum amplifier
11:16. Brake pedal
11:17. System of anti-blocking of brakes / protivobuksovochny system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment
|
Effective work of any hydraulic system is possible only after removal from it all air. Process of removal of air of the brake system is called pumping. When pumping use only new, pure brake fluid. Before pumping fill a tank with brake fluid above mark MOVE and you watch that the level of brake fluid did not fall below this mark.
Pumping order
Pumping of the brake system on models till 1998 of release with the ABS 3-channel system needs to be carried out in the following order:
– brake of the left forward wheel;
– brake of the right forward wheel;
– brake of the left back wheel;
– brake of the right back wheel.
Pumping of the brake system on models since 1998 of release with the ABS 4-channel system needs to be carried out in the following order:
– brake of the left back wheel;
– brake of the right forward wheel;
– brake of the right back wheel;
– brake of the left forward wheel.
Main method
Use of this method requires the assistant.
| PERFORMANCE ORDER |
|
1. Remove a plastic cap from the valve of production of air on a brake of the first wheel. |
|
2. Put on a rubber tube the valve. |
| 3. Lower the second end of a tube in the capacity filled with brake fluid. |
| 4. Check that the level of brake fluid in a tank was above the mark MIN and ask the assistant to squeeze out a brake pedal several times and to leave it pressed. |
| 5. Turn off the pumping valve (approximately on one turn) and wait until brake fluid flows down. When the stream of liquid stops, close the valve, ask the assistant to release slowly a pedal of a brake and check liquid level in a tank. |
| 6. Repeat point 5 until in the following brake fluid is vials of air. |
| 7. Reliably tighten the pumping valve, pick up the phone and put on a cap. |
| 8. Repeat operation of pumping on brakes of other wheels. |
|
Pumping with use of a set with the unilateral valve
In a rubber tube of such set the unilateral valve preventing hit of air and old brake fluid back in the brake system is installed. Capacity for collecting old brake fluid can be also included in the package.
Pumping with use of a set for pumping under pressure
| PERFORMANCE ORDER |
| Having connected a set for pumping under pressure to a tank of brake fluid, for pumping of system it is rather simple to open pumping valves in turn for a slitiya of old brake fluid and production of air. |
|
Check (all methods)
| PERFORMANCE ORDER |
| Upon completion of pumping wash away the spilled brake fluid, reliably twirl valves of pumping and establish on them caps. Double-check the level of brake fluid. |
|
|
|
Душевые перегородки из HPL пластика