Opel Omega

since 1993-1999 release

Repair and operation of the car


Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   - 3.1. SOHC engines of 2,0 liters
      3.1.1. Technical characteristics
      3.1.2. Check of a compression
      3.1.3. Top Dead Point (TDP) of the N1 piston
      3.1.4. Camshaft cover
      3.1.5. Pulley of a bent shaft
      3.1.6. Covers of a gas-distributing belt
      3.1.7. Gas-distributing belt
      3.1.8. Natyazhitel of a gas-distributing belt and asterisk
      3.1.9. Camshaft epiploon
      3.1.10. Casing of the camshaft and camshaft
      3.1.11. Pushers and hydraulic elevators
      3.1.12. Head of cylinders
      3.1.13. Oil pallet
      3.1.14. Oil pump
      3.1.15. Flywheel
      3.1.16. Epiploons of a bent shaft
      3.1.17. Fastenings of the engine and transmission
   + 3.2. DOHC engines of 2,0 liters
   + 3.3. 2,5 and 3,0 liters engines
   + 3.4. Partition of all petrol engines
   + 3.5. 2,0 liters diesel engine
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


785173a6

3.1.7. Gas-distributing belt

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator and remove an external cover of a gas-distributing belt.
2. Install the N1 piston in VMT.
3. Weaken a bolt (1) of a natyazhitel of a gas-distributing belt, turn the lever (2) natyazhitel clockwise against the stop and tighten a bolt.
4. Take off a gas-distributing belt and note its direction of rotation.
5. Carefully examine a belt on existence of wear and damages, if necessary replace it.

Installation

Arrangement of the index of a natyazhitel concerning a cut in a back plate

  
1. Index of a natyazhitel
2. A cut in a back plate
A. A new belt, a natyazhitel without tags
 B. A new belt, a natyazhitel with tags
C. An old belt, a natyazhitel without tags
D. An old belt, a natyazhitel with tags

PERFORMANCE ORDER
1. Carefully clean asterisks of cranked and distributive shaft. Check that synchronizing tags were combined.
2. Put on a belt asterisks.
3. Weaken a bolt of a natyazhitel and turn the lever of a natyazhitel counterclockwise against the stop. Tighten a bolt of a natyazhitel.
4. Check whether synchronizing tags are combined.
5. Turn a bent shaft on two whole revolutions.
6. Check tags and again weaken a bolt of a natyazhitel.
7. If you established a new gas-distributing belt, adjust a natyazhitel so that his index was directed to a cut or to a tag of "NEW" (see rice. An arrangement of the index of a natyazhitel concerning a cut in a back plate) also tighten a bolt.
8. If you established an old belt, the index of a natyazhitel has to be directed to 4 mm more to the left of a cut or has to indicate a tag of "USED" (see rice. An arrangement of the index of a natyazhitel concerning a cut in a back plate).
9. Establish the remained details.