Opel Omega

since 1993-1999 release

Repair and operation of the car



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines of 2,0 liters
   + 3.2. DOHC engines of 2,0 liters
   - 3.3. 2,5 and 3,0 liters engines
      3.3.1. Technical characteristics
      3.3.2. Check of a compression
      3.3.3. Top Dead Point (TDP) of the N1 piston
      3.3.4. Covers of camshafts
      3.3.5. Pulley of a bent shaft
      3.3.6. Covers of a gas-distributing belt
      3.3.7. Gas-distributing belt
      3.3.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.3.9. Epiploons of camshafts
      3.3.10. Camshafts and pushers
      3.3.11. Head of cylinders
      3.3.12. Oil pallet
      3.3.13. Oil pump
      3.3.14. Oil heater
      3.3.15. Flywheel and drive plate
      3.3.16. Epiploons of a bent shaft
      3.3.17. Fastenings of the engine and transmission
   + 3.4. Partition of all petrol engines
   + 3.5. 2,0 liters diesel engine
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


785173a6

3.3.6. Covers of a gas-distributing belt

EXTERNAL COVER

Removal

PERFORMANCE ORDER
1. Remove the preliminary camera of multiline system of an intake of air (see subsection 5.1.15).
2. Pick up the forward connecting phone of secondary system of an admission of air.
3. Take off an additional driving belt.
4. Stop a shaft of the water pump a wrench and unscrew bolts of a pulley of the water pump.
5. Remove a pulley of the water pump. In installation time new bolts will be necessary for you.
6. Stop a pulley of the pump of the hydraulic booster of steering and unscrew pulley bolts.
7. Remove a pulley. In installation time new bolts will be necessary for you.
8. Disconnect a wire from the sensor of the right number of cylinders and disconnect a wire from a cover of a gas-distributing belt.
9. Disconnect the top parts of the holder of a plait of wires which is fixed in a forward part of a cover of a gas-distributing belt. Remove a forward cover (the drawing at the left) and the right cover (the drawing on the right) the holder of a plait of wires.
10. Disconnect a wire from the valve of adjustment of exhaust gases, unscrew bolts and remove the holder of a plait of wires.
11. Unscrew bolts and remove a natyazhitel of an additional belt.
12. Unscrew bolts and remove an external cover of a gas-distributing belt.

Installation

Installation is carried out to the sequences, the return to removal.

BACK COVER

Removal

PERFORMANCE ORDER
1. Take off a gas-distributing belt.
2. Remove asterisks of camshafts, remove a pulley of a natyazhitel of a gas-distributing belt and intermediate pulleys.
3. Remove the water pump.
4. Unscrew fixing bolts of a back cover and uncover.

Installation

Installation is carried out to the sequences, the return to removal.