Opel Omega

since 1993-1999 release

Repair and operation of the car



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines of 2,0 liters
   + 3.2. DOHC engines of 2,0 liters
   + 3.3. 2,5 and 3,0 liters engines
   + 3.4. Partition of all petrol engines
   - 3.5. 2,0 liters diesel engine
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine installed in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gas distribution mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a bent shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil heater
      3.5.16. Sealing rings of a bent shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      + 3.5.19. Capital repairs of the 2,0 liters diesel engine
   + 3.6. 2,5 liters diesel six-cylinder engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. System of ignition
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, half shafts
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


785173a6

3.5.5. Gas distribution mechanism

GENERAL INFORMATION

Prevention

To check installation of the mechanism of gas distribution and the fuel pump, it is necessary to use special tools:

  – instrument of blocking of the KM932 camshaft;
  – pin of blocking of a ledge of the fuel pump KM927;
  – pin of blocking of the bent shaft KM929;
  – wrench of an asterisk of the KM933 camshaft.


Tools for adjustment of the mechanism of gas distribution

A. Pin of blocking of a bent shaft

B. Pin of blocking of a ledge of the fuel pump

C. Instrument of blocking of the camshaft

Sizes of a pin of blocking of a bent shaft


Sizes of a pin of blocking of a ledge of the fuel pump


Check and adjustment

PERFORMANCE ORDER
1. Take off an auxiliary driving belt. Unscrew an auxiliary rack of a pulley of the mechanism of a tension, the lower bolt and a hinged bolt of a basic plate of a pulley and remove the tension mechanism.
2. Remove the vacuum pump of the brake system.
3. For improvement of access to a casing of an asterisk of the fuel pump and to the pump perform the following operations:
      – remove a casing of the air filter and a reception exhaust pipe;
      – unscrew a nut from the top part of the right support of the power unit and lift the right side of the engine as far as possible.
4. Uncover a head of the block of cylinders and install the piston of the first cylinder in the top dead point in a compression step.
5. Remove the sensor of a bent shaft.
6. Unscrew screws and remove a casing of an asterisk of the fuel pump from a chain casing.
7. Check that the tag of a pulley of a bent shaft is combined with the index and insert a pulley of blocking of a bent shaft into an opening of the sensor of a bent shaft and record a bent shaft from a provorachivaniye.
8. Insert a pulley of blocking of a ledge of the fuel pump into an opening in a ledge and, moving a pulley, insert it into an opening in a pump housing.
9. Insert the instrument of blocking of the camshaft into an opening on the left end of the camshaft (it is specified by an arrow).
10. If all pins of blocking were established normally, so adjustment of the mechanism of gas distribution is not required. If at least one of pins of blocking is not established, it is necessary to make adjustment of the mechanism of gas distribution.
11. Take a pin of blocking of the pump and take a bolt on the right side of a suspension bracket from a head of the block of cylinders.
12. Unscrew the top head of a natyazhitel of a chain and take a plunger, noting situation in which it is established.
13. Fix the camshaft from turning and unscrew a bolt of fastening of an asterisk of the camshaft. Establish a new bolt, having tightened it by hand.
14. Weaken the bolts fixing an asterisk of the fuel pump to a pump ledge.
15. Check the provision of an adjusting tag (it is specified by an arrow) on the fuel pump. At the same time the top asterisk of a chain of the mechanism of gas distribution has to be combined with a pump ledge. Insert a pin of blocking of a ledge of the fuel pump and tighten bolts of fastening of an asterisk the required moment.
16. Establish a pin of blocking of the camshaft.
17. After installation of all pins of blocking put into place a camshaft asterisk, screwing up a bolt of fastening of an asterisk. At the same time support an asterisk so that sagging of a chain was from the chain tension mechanism.
18. Fix the camshaft from a provorachivaniye a wrench and in stages tighten a bolt of fastening of an asterisk of the camshaft the required moment.
19. Take all pins of blocking, establish a new sealing ring to the top head of a natyazhitel of a chain of the mechanism of gas distribution. Insert a plunger into a head of the block of cylinders and tighten it the required moment.
20. Turn a bent shaft of the engine on two whole revolutions and check that all pins of blocking can be established.
21. Check that the interfaced surfaces of a casing of an asterisk of the fuel pump and a casing of a chain pure and dry.
22. Establish a casing of an asterisk of the fuel pump on laying or a layer of sealant and fix by bolts, having tightened them the required moment.
23. Install the tension mechanism.
24. Establish a support of the power unit. Establish a cover of a head of the block of cylinders.
25. Establish a reception exhaust pipe and a casing of the air filter.
26. Install the vacuum pump of the brake system.

27. Install the sensor of a bent shaft in the block of cylinders and connect the accumulator.